Alliance Laundry Systems BF50PV Especificaciones Pagina 38
- Pagina / 162
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
F232059
36
Programming Hints
Read the Standard Cycle Charts (near the end of this
manual) for the cycles already programmed into the
computer to see how the cycle steps have been
ordered.
Use a program worksheet, such as Table 4, to write
new cycles. After the worksheet is completed, enter
the program into the computer.
The computer can do only one thing at a time, so think
in terms of what the machine should do next, step by
step. This will make it simpler to write the program.
When entering the timed portion of a step (such as a
fill), use a time that is reasonable for the local
installation. If the water pressure is low or if the water
lines are smaller than desirable, increase the time
allowed. Remember that the drain needs to empty the
machine in less than one minute. Drain times of more
than one minute are not recommended.
Except for the soak, heat, and cool-down (Wash 5)
steps, which are timed in hours and minutes, the
maximum time per step is 9 minutes and 99 seconds. If
more time is needed, add more steps to total the
complete time desired. For example, if a 15 minute
wash is desired, program a wash step for 9 minutes
and 00 seconds, immediately followed by another
wash step for 6 minutes and 00 seconds.
When a fill or addition of supplies without agitation is
desired, first program a Wash 3 step for 0 minutes and
01 seconds. Then program the fill or supply step.
When the microcomputer advances to the next step, it
will remain in the Wash Mode as programmed in the
previous step unless it is instructed to do otherwise.
Table 4
Before attempting to program any particular function
of the WE-6 microcomputer, read System
Programming, Cycle Programming, and Step
Programming.
Cycle 00
Step Description Min:sec
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
- Washer-Extractors 1
- Table of 3
- Contents 3
- Key to Symbols 6
- Operator Safety 7
- Safe Operating Environment 8
- Machine Location 9
- Input and Output Services 9
- AC Inverter Drive 10
- Operation 11
- Figure 1 12
- Figure 2 13
- Theory of Operation 14
- Wet Clean Capabilities 15
- WE-6 Microcomputer 17
- LED Display 17
- Operational Keypad 20
- Start-Up 22
- Opening Door 22
- Loading 22
- Supply Dispenser 23
- Cycle Selection 23
- Cycle Execution 23
- Test Cycle 24
- Stop Routine 25
- Balance Detection 26
- Temperature Display 27
- Figure 6 28
- WE-6 CONTROL BOARD 28
- Error Recovery Routine 29
- Thermal Overload Indicator 30
- Manual Mode Control Feature 31
- Programming 33
- Programming Tutorial 35
- Programming Hints 38
- System Programming 39
- Cycle Programming 41
- Editing a Cycle 42
- Erasing a Cycle in Memory 43
- Programming a Wet Clean Cycle 43
- Step Programming 44
- Programming Heat 49
- Programming a Wash Step 49
- Programming a Wash 5 Thermal 50
- Cool-Down 50
- Programming No Reversing 51
- Programming a Soak Step 51
- Programming a Drain Step 52
- Programming a Spin Step 52
- Programming an Auxiliary Step 52
- Transfer 54
- Figure 8 55
- Simulator 56
- Computer 57
- Preprogrammed Cycles 58
- Restaurants 59
- Shirt Laundries 59
- Standard Supply Legend 59
- Standard Cycle Charts 60
- Sample Cycle for Wet Clean 80
- Lavadoras 81
- Tabla de 83
- Seguridad 85
- Leyenda de los símbolos 86
- Entorno de operación seguro 88
- Uso indebido 90
- Figura 1 92
- Figura 2 93
- Teoría de operación 94
- Capacidades de limpieza por 95
- Pantalla de LED 97
- Microordenador WE-6 97
- Teclado de operación 100
- Output Indicators 101
- PRECAUCIÓN 102
- Distribuidor de suministro 103
- Tablas de ciclos 103
- Ejecución de los ciclos 103
- Ciclo de prueba 104
- ADVERTENCIA 105
- Detección del equilibrio 106
- Pantalla de temperatura 107
- Operación 108
- Figura 6 108
- TABLERO DE CONTROL WE-6 108
- Programación 113
- F232059 (SP) 114
- Programación del sistema 120
- Programación de un ciclo 122
- Modificación de un ciclo 123
- Programación de los pasos 125
- Modelos con 5 suministros 126
- Modelos con 8 suministros 127
- Programación de no inversión 132
- Programación de un paso de 133
- Operación del simulador y 135
- Figura 8 136
- Ciclos preprogramados 139
- Restaurantes 140
- Tablas de ciclos estándar 141
Relacionado con productos y manuales para Lavadoras Alliance Laundry Systems BF50PV
(90 paginas)
(87 paginas)
(86 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.896 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales